SHAKE CONTAINER WELL BEFORE USING TC-11

DO NOT PAINT OVER TC-11
Corrosion Protection
  1. Clean area to be treated.
  2. Allow surface to dry.
  3. Apply a light coat of TC-11 to metal surfaces. Repeat process 3-4 times a year.
Rust Removal
  1. Spray area with TC-11.
  2. Use a paper towel, cloth, 0000 steel wool or a stainless steel wire brush to agitate surface.
  3. Clean area with a water spray, paper towel or cloth. Repeat steps 1-3 if necessary
Freeing Frozen Bolts and Parts

TC-11’s superb penetrating characteristics easily fill the interstial spaces in frozen parts for unparalleled unlocking of frozen bolts and parts.

  1. Spray frozen bolt or part with TC-11.
  2. Wait 10-30 seconds.
  3. Apply torque in a back-and-forth motion. Repeat steps 1 to 3 if necessary.
Lubrication
  1. Apply a small amount of TC-11 to the moving metal parts.
  2. After 20 minutes, wipe off excess TC-11.
Electrical System Waterproofing

Apply TC-11 to spark plug boots, distributor cap, coil or coils, battery terminals, multi-pin connectors, and terminal strips. Do not apply directly to fuse labels or other sensitive adhesive labels. Do not apply to arcing contacts. TC-11 is an insulator that will cause a small voltage drop across the connection that does not increase over time. An untreated connector will corrode and the voltage drop will increase until the component no longer functions.

Long-Term Storage: If equipment is to be stored for more than five months, apply a heavy coat of TC-11, wait 20 minutes, and apply a second heavy coat. Wash down equipment with a water spray to remove any dust and debris.

Application Specific Directions
Locks
  1. Flush frozen locks and drain vertically overnight.
  2. For operating locks, put a small drop of TC-11 on a key and insert the key into the lock. Repeat application annually.
Bicycles
  1. Apply TC-11 to metal surfaces.
  2. Let the TC-11 set for 20 minutes.
  3. Hose down bicycle.
  4. Apply a small amount of TC-11 to the drive chain, pivots, and cable sleeve ends. Repeat process 3 times a year.
Boats
  1. Clean metal parts with a cloth or a degreaser and a water rinse according to all environmental rules and regulations.
  2. Allow surface to dry thoroughly.
  3. Restore primer film and paint film as necessary.
  4. Apply TC-11 to all metal parts. Repeat steps 1– 4 every 3 months.
Vehicles

Apply to metal engine parts, throttle sleeve ends and linkages, transmission, undercarriage, locks, hinges, and door tracks twice a year. Do not apply TC-11 to the radiator or A/C condenser fins, brake rotors, or brake pads.
Preventing vehicle damage due to road salt
  1. Make sure that paint and undercoating are in good condition.
  2. Wash down undercarriage.
  3. Allow undercarriage to dry.
  4. Apply a heavy coat of TC-11 to the entire undercarriage.
  5. Allow the TC-11 to set for 20 minutes.
  6. Apply a second heavy coat of TC-11. Repeat steps 1-6 at beginning, middle, and end of snow season.
Household
  1. Apply to tools, window operators, locks, and hinges on an annual basis.
  2. TC-11 removes rust stains from porcelain and fiberglass quickly and easily.
  3. TC-11 removes adhesive residues and indelible ink.
Sporting Goods
  1. Apply TC-11 to fishing reels, guns, PWC, ATVs and other metal equipment 48 hours prior to use.
  2. Clean equipment after use.
  3. Allow equipment to dry.
  4. Apply a thin coat of TC-11. Apply two thick coats of TC-11 before long-term storage periods.

I put TC-11 on a metal overhead door that was difficult to operate and it was making a lot of noise. As soon as I put TC-11 in the operating mechanism, it was much easier to operate and it no longer made any noise. The amazing thing is that this was three years ago, and the TC-11 is still doing its job. When I applied the TC-11 some of the over spray landed in a fish pond that was below the door. I figured that the fish were in big trouble. It turned out that the TC-11 had no effect on the fish. I recommend the product to everyone.

GLEN - KAILUA, HAWAII

 BUY TC-11 NOW!